Yardworks Grass trimmer/edger Manual do Operador

To reduce the risk of injury, the user must read and understand the operator’s manual.Save this manual.25.4cc Line Trimmer25.4cc Ezy Load Line Trimme

AssemblyAttaching the Front Handle(Model Nos. 101PLT25, 101PLT25SS,101PLT25D, 101PBC33)See Fig. 2Follow these steps to attach the front handle.1.Remov

Assembly – continuedInstalling the Line TrimmerHead AssemblyBrushcutter – Model Nos. 101PBC33,101PLT25SS and 101PBC33BHSee Fig. 5Follow these steps to

Assembly – continuedInstalling the Ezy Load Line Trimmer HeadLine Trimmer – Model No. 101PLT25DSee Fig. 7Follow these steps to attach the Ezy Load Lin

13Attaching the Grass Deflector GuardNOTE: To protect the operator, always be sureto attach the grass deflector.To attach the Curved ShaftGrass Def

14OperationMixing the fuelThis product is powered by a 2 stroke engineand requires pre-mixing petrol and 2 stroke oil.The oil mix should be 25:1. Neve

15Starting the ProductStarting the product depends on whether the engine is cold or warm.Operation – continuedThe recoil starter can be damaged by abu

16IMPORTANT: For maximum performance andoperating life, allow engine to warm before use.1. Run the engine at idle speed untiloperating temperature is

17Operating the Line TrimmerSee Fig. 12Follow these steps to operate the line trimmer:Fig. 121. Start the trimmer.2. Hold the trimmer at waist level w

Do not cut with a dull, cracked ordamaged metal blade. Before cuttinggrowth, inspect for obstructions suchas rocks, metal stakes or strands ofwire fro

Installing the Blade GuardModel Nos. 101PBC33. 101PBC33BH and 101PLT25SSSee Fig. 15Follow these steps to install the blade guard onto the blade.Fig. 1

Before you use your new trimmer/brushcutter, read this manual carefully tolearn how to operate and maintain your product correctly. Reading this manua

Maintenance20Emissions Maintenance ScheduleMaintenance, replacement or repair of the emission control device and systems may beperformed by any author

Replacing the Cutting LineSee Fig. 16Follow these steps to replace the cutting line:BEFORE EACH USE: Remove dirt and debris from the productexterior.

2. Remove the spark plug boot.3. Remove the retaining cap by turningcounter clockwise.4. Remove the spring.5. Remove the empty spool.6. Cut 2 lengths

Replacing the Spark PlugNOTE: Before removing the spark plug,thoroughly clean the spark plug and cylinderhead area.Model Nos. 101PLT25, 101PLT25D and

Troubleshooting:24Problem Possible Cause SolutionEngine will not start 1. Set switch to the ON position.2. Remove the spark plug. Re-attach the spark

Warranty25Petrol Operated Products Limited WarrantyPope warrants to the original retail purchaser that this Petrol Powered Product is free from defect

Authorised Pope Service DealersAUST. CAPITAL TERRITORYMitchell LawnmowerCentreMITCHELL(02) 6241 4806NEW SOUTH WALESAgrifarm ImplementsTAREE(02) 6552 6

ContentsSafety Rules ...

Physical Condition of the Operator. Donot operate this product when tired, ill orunder the influence of alcohol, drugs ormedication. Clothing Requi

Save These InstructionsSymbolsThe following symbols are located on the product. Please study them and learn their meaning.Proper interpretation of the

Specifications6Model 101PLT25Curved Shaft Line TrimmerEngine: 25.4 cc Full CrankCutting Width: 35cmLine Size: 1.6mm to 1.8mmWeight (Dry): 4.7 kgFuel T

ApplicationsUse this product for the following applications: Cutting grass, weeds and light undergrowth (all models) Edging along paths and driveway

FeaturesYour new product is equipped with thefollowing features. EngineThe engine is powerful and easy to start. It iseffectively counterbalanced, whi

UnpackingInstructions Carefully remove the product from the box. Inspect the product carefully to make sureno breakage or damage occurred duringship